Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
They are making a number of good pointers about How to Install a Bathtub overall in this article underneath.
Installing a tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a new one is additionally a moderately tough job. If the old bathtub is easily easily accessible, the task can move rapidly; if you have to open a wall to get rid of the old tub and also place the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will require a helper to leave the old bathtub and also set in the new one. See to it you have certified yourself for the work as well as are comfortable attempting it. As opposed to hiring a contractor to take over a halfway-completed project, it is better to take into consideration utilizing one before you start. Possibilities are you might require an expert plumber to make tube connections.
This short article will certainly aid you set up a brand-new tub in your washroom if you have actually currently purchased a new tub and also do not require to transform the plan of your previous supply of water pipelines.
Your devices as well as product checklist ought to comprise the following:
Getting ready for the Installment
First of all, the supporting structure supplied with the bathroom should be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its final placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, then the first thing you should do is detach the water system. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of eliminating the existing taps can be quite troublesome due to the restricted access that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel all set for the continuing to be water that will come from the pipelines. When the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Making use of both wood boards under its feet, put the bathtub in the required placement. The wooden boards are helpful in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bath tub until the level reviews degree.
To mount taps, fit all-time low of the outermost flexible faucet connector to the suitable supply pipe by making a compression join; after that do the exact same for the various other tap.
Switch on the water supply and also inspect all joints and new pipework for leakages and also tighten them if necessary. Fill up the bathtub and also examine the overflow electrical outlet and the normal electrical outlet for leaks.
Ultimately, fix the bath paneling as described in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait up until the tub has been utilized a minimum of when as this will certainly resolve it right into its final placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place in between the tap as well as the sink. Protect the faucet in position with the maker given backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The former kind must be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to break an inflexible seal, causing the water to penetrate the wall surface between the bath and the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your components and fittings. They are marketed in tubes and also cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always load the tub with water prior to sealing, to enable the motion experienced when the bathtub is in use. The sealant can crack rather early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily available on the market. It is recommended to fit the tiles utilizing water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our piece on Installing A Bathtub. Thanks so much for taking a few minutes to read through our blog post. Sharing is good. Helping people is fun. Thanks for your time. Come back soon.
Emergency? Call us! Report this page